How to change the cabin filter on a Chevrolet Niva?

The filter element guards the cleanliness of the air entering the cabin. It is he who has to pass a huge amount of air through himself and cleanse the contaminants that fill the road air. Its structure contains a paper sheet that allows air to pass through itself, while dust particles remain on the sheet. Over time, the paper accumulates a lot of contaminants, which negatively affects the throughput and the operation of the interior ventilation system. The best way to check whether an element is dirty is to remove it and look at the amount of debris in its ribs. It can also be determined by indirect signs such as: poor ventilation of the stove and an unpleasant odor when the heater is turned on. The Chevrolet Niva (21214) is equipped with both conventional paper elements and those with activated carbon (for better air purification). Which one to choose is up to you.

Where is the filter located?

The cabin filter in a Chevrolet Niva car is located on the ventilation duct, which is an air intake. It can be found on the right side of the windshield under the plastic trim, which is located on the windshield wiper trapezoid, secured with a self-tapping screw.

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

It should be noted again that the role of the cabin filter is great. And if it becomes clogged, it must be replaced as soon as possible. Most practicing car enthusiasts recommend purchasing a new filter to change, which is produced with article number NF-6004.

The cost of a cabin filter in a Chevrolet NIVA ranges from 160 to 310 rubles. In addition, you must definitely purchase fresh sealant, the price of which is approximately 120 rubles. However, when installing a cabin Nevsky filter, it often turns out that the dimensions do not match. The cabin filter of the named company has a larger seat than is expected in this car.

In this regard, many car owners prefer to purchase analog cabin filters, which are in no way inferior in quality to the original.

Such filters are slightly smaller in size and, in addition, have a soft frame and a foam rubber seal. This makes it easy to install the device and ensure high-quality cleaning of the air entering the cabin. The technical specifications recommend changing the cabin filter depending on the conditions in which the car is operated, but at least once every six months or a year.

However, experts recommend that car owners rely on personal feelings. If any health problems arise, the filter must be replaced. Since its purpose is to provide comfortable conditions for the driver and passengers. Most practitioners believe that the filter needs to be replaced in early spring and autumn. If the filter is not changed for a long time, this can lead to the appearance of mold in the filter and the spread of bacteria in the car. And, as a rule, it is almost impossible to remove mold.

Choosing a cabin filter for a Chevrolet Niva

(1.7 / 4×4 / 80 hp), (1.7 / 4×4 / 83 hp), (1.8 / 4×4 / 125 hp)

Problems often arise when choosing cleaning elements on your own. The reason is that the owners do not know the markings and catalog numbers, as a result of which spare parts are purchased that do not meet the requirements of the given vehicle.

To avoid emergency situations, we recommend purchasing parts exclusively from specialized stores, dealership centers, and official representative offices. As an alternative, order spare parts for subsequent installation at certified workshops. This practice is gaining momentum and spreading at a rapid pace.

Original and verified catalog items:

• Bosch, 1987432333, price from 300 rubles. Parameters: 25.2 x 15.4 x 3.50 cm;
• Champion, CCF0420, from 300 rubles;
• Knecht Filter, LA 934, from 300 rubles;
• LYNXauto, LAC1907, from 300 rubles;
• LYNXauto, LAC1907C, from 300 rubles;
• MANN-FILTER, CU26005, from 300 rubles;
• Patron, PF2266, from 300 rubles;
• Sakura, CA25055, from 300 rubles;
• CHAMPION, CCF0433, from 350 rubles;
• MANN-FILTER, CU26019, from 350 rubles;
• FILTRON, K1230, from 350 rubles;
• KNECHT, LA939, from 350 rubles;
• DENCKERMANN, M110899, from 350 rubles;
• PATRON, PF2266, from 350 rubles;
• KNECHT, LA 937, from 350 rubles;
• CHAMPION, CCF0508, from 350 rubles;
• MANN-FILTER, CU26011, from 350 rubles;
• FILTRON, K1222, from 350 rubles;
• DENCKERMANN, M110800, from 350 rubles.

There is no data regarding the compatibility of other filter modifications. All actions are under the personal responsibility of the driver. To avoid incorrect installation, always use proven consumables.

When to change the filter

The filter is part of the forced air circulation system, which is performed by the on-board air conditioner. Of course, there are certain sanitary standards for changing the cleaner, but the degree of its contamination depends on the following factors:

• where exactly do you operate your car (dirt roads or asphalt);
• how often do you use your car?
• do you keep it clean?

We recommend: Changing the VAZ 2110 crankshaft oil seal yourself

Auto mechanics at the official Chevrolet showroom advise changing this part every six months or after 10-15 thousand kilometers. Usually, according to the rules, it is recommended to replace them in early spring and then in the fall.

Remember, the air barrier has a warm, damp environment in which all kinds of fungi and hard-to-remove mold thrive.

Timing for replacing the cabin filter

The cabin filter in a car is an unremarkable detail that is hidden from prying eyes. It is located behind the glove compartment and does not attract attention until an unpleasant odor appears in the cabin. Also, when the SF is polluted, windows often fog up, and the stove and fan function poorly, even at maximum speed.

A malfunction of the cabin air filter can also be detected during an external inspection, but to do this it will be necessary to remove the glove compartment. For this reason, many drivers are in no hurry to change the SF, and in vain!

The cabin filter not only cleans the air in the cabin from dust and dirt. This element also holds plant pollen and pathogenic bacteria on the surface, which have a detrimental effect on human health.

Today SF is installed in every car. At the same time, the part is not durable and requires replacement after a certain mileage - 15-20 thousand km. In some cases, filtration is changed more often, depending on the operating conditions of the vehicle.

On a Chevrolet Niva, the cabin filter is replaced during scheduled maintenance. However, this work is not difficult, and any driver, even a novice, can handle it, provided that the instructions described below are followed.

Regulations

According to the automaker's regulations, replacing the Niva Chevrolet cabin filter should be carried out once every 15,000 km. Meanwhile, if you drive in a very dusty area, it is recommended to carry out work more often. Therefore, many owners prefer to change it every 10,000, or even 7,000 km.

Some car enthusiasts clean such an element by shaking it out and blowing it with air. However, this cannot fully ensure its cleansing, so it can only be used as an additional measure after out-of-town trips.

Step-by-step replacement instructions

Replacing the cabin filter in a Niva Chevrolet is a simple process, but since it has to be done systematically, be sure to read the detailed instructions.

Where is?

Location of the barrier under the hood

The cabin filter element in the Niva Chevrolet is located under the trim, in front and slightly to the right. To gain access to it, you need to unscrew one screw and remove the cover.

What will you need?

The replacement process is simple and does not require many special tools:

• new cabin filter;
• sealing compound;
• rags;
• screwdriver.

Stages

Before replacing, you need to turn off the engine, turn on neutral speed and set the car to the handbrake.

1. Unscrew the screw using a screwdriver and carefully pry off the cover.

   Raise the lid

2. We take out the filter filter.

   We pry up and take out the filter element

3. Using a rag, clean the body from dust.
4. We clean the housing from the remaining sealant around the perimeter. It is better to do this with sandpaper.
5. We print out a new filter and put it with foam on top.

   We install a new one

6. We treat the contour with new sealant.
7. We put the cover in place and tighten the self-tapping screw.
8. We turn on the engine, check the car, turn on the heater.

Filter location

Self-tapping screw that needs to be unscrewed

Old element

Retrieving the old element

New filter material installed

We install a new one

If everything works fine, then we can consider the work finished. If anything is still unclear, watch the video.

How often should I replace?

The operating instructions indicate a replacement interval of 30,000 km. mileage In practice, few people use the recommendation, since the figure is too high and not acceptable for domestic road transport. Those owners who take care of their equipment always update consumables every 10–12 km. mileage The resource best corresponds to the quality of manufacturing of spare parts, components, and climatic conditions.

In the case when the car is used in conditions of increased dustiness and gas pollution, the replacement interval for the cabin filter is reduced to 8000 km. However, nothing prohibits owners from replacing them at an interval of 30,000 km, as required by the instructions.

In what cases is it justified to replace the filter:

• There is a weak air flow coming from the deflectors, none at all;
• the smell of rot, rot, and stench can be heard in the car’s interior;
• debris particles fly out of the deflectors, which indicates that the filter is clogged;
• major repairs of a car due to an impact, accident, collision;
• planned replacement during technical inspection.

Filter selection

Typically, car enthusiasts choose a new Chevrolet Niva cabin filter produced by the Nevsky Filter company (product order number NF-6004). But the size of such a device is often larger than the seat. Therefore, many owners install filters from the manufacturer Kalina with catalog number 11180-8122010-82 - for a regular filter and 11180-8122010-83 - with carbon filler.

The dimensions of these filters are slightly smaller, but they have a soft frame and a foam seal around the perimeter. Due to this, the devices easily fit into place and provide good air purification. Other manufacturers of quality filter elements are Big Filter (part number GB-9831) and TSN (part number 9.7.26).

How to replace

You can replace the cabin filter yourself; there is nothing complicated about this procedure. The frequency of changes depends on the operating conditions of the vehicle. The dustier the area you move through, the more often you need to change it. There are two replacement methods: one with complete or partial dismantling of the frill; the other - through a special hatch made specifically for these purposes.

Method 1

1. Open the hood lid and unscrew the screw that secures the hatch to the frill on the passenger side.
2. Cut off the sealant from the lid and open the hatch.
3. Remove the old filter (take it out carefully so that dust and dirt accumulated on it do not spill into the heater air duct).

4. We remove the packaging from the new element and firmly install it in place of the old one (it must be facing the right way, for this there is an arrow in the direction of flow on the frame).
5. We clean off the old sealing material from the lid and the frill itself, and apply a new one around the entire perimeter of the lid (sealing is needed to prevent water from entering the interior ventilation system).

6. We install the lid in its place and remove the excess sealing material (for peace of mind, you can apply sealants around the entire perimeter of the lid and on top).

7. We check the operation of the heater in all operating modes.

Method 2

To replace with partial removal of the trim under the windshield you need:

1. Raise the hood and unscrew the frill fastenings (six screws, all on top).
2. Lift the edge of the lining and remove the old filter element.
3. After removing the dirt and dust accumulated there, install a new filter.
4. Reassemble everything in reverse order.

These recommendations are suitable for anyone who is thinking about how to change the cabin filter. The second method is more suitable for those who do not have sealant or silicone on hand; you need to unscrew more screws, but the time will be the same.

Article rating:

Loading…

Share with friends: Add a comment

Work progress

The process of replacing the Chevrolet Niva cabin filter can be carried out in one of 2 ways, which differ slightly in the dismantling algorithm:

1. Plastic cover.
2. Frill parts.

First option

To remove the cover, you need to unscrew the fixing screw and cut off the sealant.

Next you need to remove the replacement filter element. To do this, you can pry it off with a screwdriver.

You need to work extremely carefully and do not shake the element so that dust and dirt accumulated in it do not spill into the air duct.

Next, in accordance with the attached instructions and the direction of the arrow, a new Chevrolet Niva cabin filter is installed.

Then you need to thoroughly clean the lid, degrease the working surface, apply new sealant, install the plug in place and secure it with a self-tapping screw.

Second option

It involves removing part of the frill so as not to touch the lid, which is seated on the sealant. By the way, many owners note that this is even faster.

To do this, you need to lift the hood, and then unscrew the screws that secure the frill. There are 6 screws in total, and they are all located on top.

Lift the plastic and carefully remove the used filter element. Install a new one in its place and tighten the screws.

The process of replacing the Chevrolet Niva cabin filter yourself is demonstrated in the video below.

Replacing the filter

All Chevrolet Niva cars produced are equipped with a cabin filter. Over time, the filter may become clogged with dust and stop filtering the air. In this case, the equipment must be updated every 15,000 km.

If the car is used in difficult climatic conditions, when the air is heavily dusty, then the filter is changed every six months. Most often, the cabin filter needs to be changed if the following problems arise:

• Windows fog up in the cold season because the heating system fan is not able to provide sufficient air flow.
• Cars with air conditioning smell of dust and other contaminants.

If the equipment is not replaced in the listed cases, this may result in problems with the radiator of the air purification system, which is unlikely to be cleaned.

It is quite possible to replace the cabin filter in a Chevrolet NIVA not at a service station, but with your own hands. For self-installation, you must prepare the following equipment and tools:

• New filter.
• Silicone sealant to seal the lid.
• A screwdriver with a Phillips and a flat blade.
• It is advisable to watch a video on the Internet that will show how to quickly and efficiently install an unused filter.

The cabin filter is replaced according to the following algorithm:

• First of all, use a Phillips screwdriver to unscrew the screw that holds the cover in place.
• Using a flat blade screwdriver, install the lid and frill tightly together. Lift the roof up and then remove it.
• The old filter is then removed.
• The area where the filter was located is cleared of dust and other contaminants.
• After this, a new filter is installed.
• The filter must be installed in the direction of the flow in which the air moves. This direction is indicated by an arrow on the filter.
• The cover is lubricated with fresh sealant and installed in its original place.

The installation is completed by tightening one or more screws.

As a result, it should be said that you can replace the cabin filter in a Chevrolet NIVA yourself and it will not take much time. But it is precisely this action that will be able to protect the driver and passengers from serious health problems in the future.

Tired of paying fines? There is an exit!

Forget about fines from cameras! An absolutely legal new product - Traffic Police Camera Jammer, hides your license plates from the cameras that are installed in all cities. More details at the link.

• Absolutely legal (Article 12.2);
• Hides from photo and video recording;
• Suitable for all cars;
• Works through the cigarette lighter connector;
• Does not cause interference to radios and cell phones.

Find out details

Choosing a cabin filter

Today, all SFs are divided into two types:

• standard (anti-dust) devices;
• coal SF.

Standard filter devices are made of corrugated cardboard or synthetic fiber. The surface of the SF is multi-layered, due to which the atmospheric flow passes through several degrees of purification. The filter retains dirt, dust, leaves, pollen, and exhaust gases by 96%!

Coal SF, in turn, can also neutralize unpleasant odors in the cabin and additionally have antimicrobial properties.

When choosing a new filter device for the interior of a Chevrolet Niva car, you should follow the instructions from the manufacturer. It is important to purchase a model that is suitable in size.

Preparing for replacement

In order to replace the cabin filter in a Chevrolet Niva, you need to prepare the following tools:

• clean rags;
• new air filter;
• means for cleaning the seat;
• crosshead screwdriver;
• sealant.

The process of replacing the cabin filter

Step-by-step instructions for replacing the SF in a Chevrolet Niva:

• Open the hood, unscrew the cover bolts.
• Unclip the cassette latches.
• Carefully remove the old air filter.
• Wipe the seat with a clean rag.
• Insert a new SF into the cassette according to the “UP” and “DOWN” indicators.
• Treat the protective cover with sealant and tighten the screws.

This completes the installation procedure for the new SF.

Replacing the cabin filter on a Chevy Niva is performed in a similar sequence.

When is it necessary to change the cabin filter material?

However, all of the above problems can be avoided if you simply change the filter at the appointed time. The manual that comes with the car indicates when to replace the filter. But in this matter it is better to proceed from personal feelings when examining the cabin filter element.

Certain models have special sensors that indicate the degree of contamination of the air barrier.

When choosing a new filter, be sure to take into account that those that contain activated carbon in their composition will last much longer when compared with conventional paper ones, including if they have a bactericidal coating.

How to change the Chevrolet Niva cabin filter?

Despite its simplicity and even some primitiveness, the cabin air barrier performs a very important function. First of all, it prevents fumes, dust particles, and various microorganisms from entering the car interior. In addition, it perfectly prevents the entry of small insects, pollen and third-party odors. That is why replacing the Chevrolet Niva cabin filter is a very important and crucial moment in car servicing. But gradually the filter material loses its cleaning properties and even becomes a source of spreading not only dirt and dust, but also dangerous bacteria.

Old and new barrier
Changing the cabin filter element is determined by its maintenance regulations and attention not only to one’s own well-being and health, but also to those of passengers. The time to change the cabin cleaning element is determined by a number of different factors. First of all, it is necessary to take into account the conditions in which the car is operated. For example, if you mainly drive on dirt roads, which are significantly different from asphalt roads because they are more dusty, then you will need to replace the filter much earlier than indicated in the instructions that come with the car. According to car service professionals, the cabin filter element should be changed every 15 thousand kilometers. If you drive rarely and on well-paved roads, then you can change the filter material less often. However, be that as it may, this period must be within six months. In this matter, it would be a good idea to take the advice of experts who recommend replacing the cabin filter every six months at the beginning of autumn and spring.

The cabin cleaning barrier is a difficult filter material, since the comfort inside the car depends on its condition, but the main thing is that it prevents harmful substances from entering the cabin, which ultimately end up in the lungs of passengers, which can lead to various colds and allergic diseases. And this is doubly dangerous if there are small children in the cabin.

After the specified active period of use has expired, the filtering characteristics of the system are significantly reduced and it retains less and less all kinds of harmful substances and microorganisms.

If the filter has not been replaced for a long time, it can become a breeding ground for mold, which will be quite difficult to remove later.

A dirty filter is an ideal environment for bacteria to grow, also because the cabin cleaner is located in a place where ultraviolet rays do not penetrate. It is these dark, damp and warm places that are the best place for fungi to grow. This is especially true for inexpensive element filters, since they do not provide disinfectant impregnation.

[Hide]