DIY Motorcycle
To make a motorcycle, you will need:
Draw a motorcycle frame on cardboard. We mark the locations of the wheels. Cut out the motorcycle frame.
We make the motorcycle frame from thick packaging cardboard from three identical parts for strength. Cut holes for the wheel axle.
We put the motorcycle frame parts together and fasten them with a stapler. We mark on the frame the place where the gas tank is attached (a Kinder Surprise egg) and cut out the excess cardboard.
Wrap the Kinder Surprise egg in foil. Attach the gas tank using tape. We roll a cylinder out of paper (an axle for wheels) and glue it together.
We insert the wheel axle into the hole on the motorcycle frame and fasten the wheels. We do the same for the second wheel. If necessary, secure the wheels with tape.
We pierce the motorcycle frame with an awl, insert a toothpick and put plugs on both sides of the frame - this is the motorcycle engine. We cut the toothpick.
We fold two cocktail tubes, cut them, fasten them together with tape and put them on the motorcycle frame - this is the steering wheel. We make 2 cylinders from paper with a diameter of a pencil and a length of about 7 cm.
We wrap the cylinders in foil - these are motorcycle exhaust pipes.
We attach the exhaust pipes to the motorcycle frame using tape. The motorcycle seat can be made of foam rubber and secured with toothpicks. The motorcycle is ready.
Source
Creative machines - paper crafts (full instructions)
We accumulate quite a lot of tubes after using toilet paper. And if we used to throw them away, now we decided to make crafts out of them. The results were such wonderful machines. Do you want the same? Let's get started!
We will need:
- Scissors or knife
- Glue
- Brush
- Toilet paper tubes
- Acrylic paints
- Cardboard
- White and colored paper (for decoration)
- Small nails or buttons
- Pencil
Features of paper motor vehicles
A paper motorcycle model consists of many large and small parts and elements. Therefore, you should carefully study the sequence of correct assembly so that all components of the structure fit perfectly together and form a single composition.
If desired, the motorcycle can be made from white paper (in mono color), or a smaller copy of the analogue can be made by selecting all the corresponding colors from colored paper. A model in which small details will be painted with paint, for example (like chrome-plated metal), silver, will look beautiful. To make a round mirror (motorcycle accessory), you can take foil.
You can make footpegs so that the finished motorcycle model has additional support in the middle, and is more stable and looks impressive.
Examples of ready-made crafts and paper designs
You can explore different options for motorcycle crafts - from the most basic to complex motorcycle models, then get creative. And for the most “advanced” it will not be difficult to assemble large-scale models of motorcycles.
Making a motorcycle out of paper
In order to make a YAMAHA motorcycle out of paper, you need to print out diagrams - patterns of all the parts that are drawn in Figures 1-18. It is better to print them on cardboard, as this will give the model strength. It is also advisable that the printer on which you will print is color, then the motorcycle model will turn out bright. However, if you print it on a black and white printer, it doesn’t matter. Black and white diagrams can be colored manually with felt-tip pens.
After the diagrams with the parts are printed, you just have to cut them out and glue them, strictly according to serial numbers.
How to make a motorcycle
To figure out how to make a motorcycle out of paper, you should familiarize yourself in detail with the diagram of the technique, carefully cut out all the necessary elements from paper, and assemble the craft step by step.
Required materials and tools
Before you start making a motorcycle out of paper with your own hands, you should prepare all the materials for work:
To make an applique on the base, you need cardboard, frames (for decoration), braid or rope (for hanging), or a stand (for installation). You may need wire, toothpicks and other small elements to better secure the parts of the entire structure.
Step-by-step assembly of a three-dimensional craft from modules
An original craft made using the technique of a modular origami motorcycle, upon completion of the work, will become a real decoration of the collection.
How to make a motorcycle out of paper with your own hands
Traditional weekend craft made from paper. Download the file and print it on a color printer and thick paper; if you don’t have a color printer, you can print it in black and white and, if you wish, apply your own coloring to the motorcycle. Download the file with motorcycle parts . Tools and materials - scissors, glue and ruler.
The Harley Davidson motorcycle assembly diagram is as follows:
Step 1. Cut out all the parts of the motorcycle with scissors.
Step 2. We trace the bend lines with a blunt object. See photos and videos.
Step 3. We bend the parts of the toy along the lines.
Step 4. Glue the parts of the Harley Davidson motorcycle together. Recommended assembly sequence. Glue the frame with the wheels. Do not glue the front wheel struts together. Glue the steering wheel with the headlight unit and the gas tank, glue the seat, motor and finally glue the muffler strut to the wheel.
Harley Davidson motorcycle blank Cut out the parts Motorcycle parts Mark the bend lines Glue the parts together Harley Davidson motorcycle
As you can see, the collection of equipment has been replenished with one more craft. But such a Harley Davidson motorcycle can also be a gift, for example, on February 23rd.
Don't forget to share the link to the motorcycle or add it to your favorites.
Build a toy Harley Davidson motorcycle out of paper yourself, with a friend, brother, son, grandson.
Cutting templates
The use of ready-made templates significantly saves time; you do not need to make a drawing yourself or calculate dimensions, which, when designed independently, cannot always guarantee the joining of parts of the entire structure. All you have to do is choose the option you like, print it out, and start the creative process - the craft is always successful on the first try.
Thus, a self-made motorcycle from cardboard or colored paper is an original, spectacular craft. Guided by diagrams, videos and step-by-step assemblies, the motorcycle structure will be easy to assemble. And the finished model of equipment will delight the eye for a long time, adding to the collection of crafts.
Source
Model of a motorcycle from scrap materials (17 photos)
I sketched out a simple drawing of the frame on paper and selected resistors of suitable sizes:
After assembling the frame, I moved on to the wheels, I took the disks and pancake fasteners from hard disks as a basis, selected the beads in size and a couple of gears:
Having assembled the model a little, I also realized that the frame and the motorcycle itself were somehow flimsy and unreliable and did not look as good as I would like, so I decided to change the concept a little and took copper wire as a basis. Wire frame:
added a spring-loaded seat to the frame:
This design turned out to be much stronger, and in my opinion it looks much better.
Then I took thin copper plates and made the rear wing:
and behind it, from the same plate, by cutting and soldering, I made a fuel tank:
I made a fork for the front wheel from a wire, bent a steering wheel from a thinner wire, and wound springs from an even thinner wire. I collected everything in a pile and hung the parts in their places:
Then it was time for the engine, I puzzled over it for a long time, then I found a wire (tin solder) of a suitable size and began to knock out and grind out the cylinders:
I added some kind of gearbox to the engine, made fins on the cylinders and added wires that in the original go to the spark plugs:
I made an exhaust system from wire and tubes:
Covered the seat with leatherette. I made a simple case out of it:
And then I put everything together, made a headlight from a plastic cylinder and transparent plastic, finished the steering wheel, adding rear-view mirrors and handles. And painting, so as not to rack my brains for a long time, I took nail polish, it goes on quite well, there are interesting colors and dries quickly.
Motorcycle model from scrap materials
Last time I posted photos of my crafts made from old radio parts. A friend saw them and gave me the idea to build a motorcycle, I liked the idea. After racking my brains a little, I began to select parts and began assembly.
I sketched out a simple drawing of the frame on paper and selected resistors of suitable sizes:
After assembling the frame, I moved on to the wheels, I took the disks and pancake fasteners from hard disks as a basis, selected the beads in size and a couple of gears:
Having assembled the model a little, I also realized that the frame and the motorcycle itself were somehow flimsy and unreliable and did not look as good as I would like, so I decided to change the concept a little and took copper wire as a basis. Wire frame:
added a spring-loaded seat to the frame:
This design turned out to be much stronger, and in my opinion it looks much better.
Then I took thin copper plates and made the rear wing:
and behind it, from the same plate, by cutting and soldering, I made a fuel tank:
I made a fork for the front wheel from a wire, bent a steering wheel from a thinner wire, and wound springs from an even thinner wire. I collected everything in a pile and hung the parts in their places:
Then it was time for the engine, I puzzled over it for a long time, then I found a wire (tin solder) of a suitable size and began to knock out and grind out the cylinders:
I added some kind of gearbox to the engine, made fins on the cylinders and added wires that in the original go to the spark plugs:
I made an exhaust system from wire and tubes:
Covered the seat with leatherette. I made a simple case out of it:
And then I put everything together, made a headlight from a plastic cylinder and transparent plastic, finished the steering wheel, adding rear-view mirrors and handles.
And painting, so as not to rack my brains for a long time, I took nail polish, it goes on quite well, there are interesting colors and dries quickly.
A few photos of the finished bike:
This is my first such experience and I really enjoyed the creation process. This motorcycle is already going away as a gift. By the way, a very good gift option for bikers and just motorcycle enthusiasts)
Did you like the article? Subscribe to the channel to stay up to date with the most interesting materials
Source
How to make a motorcycle out of paper with your own hands
Traditional weekend craft made from paper. Download the file and print it on a color printer and thick paper; if you don’t have a color printer, you can print it in black and white and, if you wish, apply your own coloring to the motorcycle. Download the file with motorcycle parts . Tools and materials - scissors, glue and ruler.
The Harley Davidson motorcycle assembly diagram is as follows:
Step 1. Cut out all the parts of the motorcycle with scissors.
Step 2. We trace the bend lines with a blunt object. See photos and videos.
Step 3. We bend the parts of the toy along the lines.
Step 4. Glue the parts of the Harley Davidson motorcycle together. Recommended assembly sequence. Glue the frame with the wheels. Do not glue the front wheel struts together. Glue the steering wheel with the headlight unit and the gas tank, glue the seat, motor and finally glue the muffler strut to the wheel.
Harley Davidson motorcycle blank Cut out the parts Motorcycle parts Mark the bend lines Glue the parts together Harley Davidson motorcycle
As you can see, the collection of equipment has been replenished with one more craft. But such a Harley Davidson motorcycle can also be a gift, for example, on February 23rd.
How to make a motorcycle from plasticine?
join the discussion
Share with your friends
Using plasticine, you can create many original vehicles, and a motorcycle is no exception. This craft includes a huge number of details, so a child may not be able to cope with it on his own, as a result of which he will need the help of an adult.
Paper origami machines (diagrams)
Origami racing car
Such cars were popular in the USSR. We also post a video:
Origami tank
Origami machine
Simple option
Gray plasticine is taken to form the main element of the motorcycle. To do this, it will be necessary to give the material a rounded shape, and its right side will need to be slightly extended. An oval shape is created from a red piece of plasticine, which will act as a fuel tank.
In addition, the seats, which are distinguished by their oblong shape, are made from the same material in the same color scheme. In order to achieve the curvature of the seats, you can press lightly on them. After this, the two parts are fastened together. The main part of the plasticine is under the seat. To create the wheels, black and gray plasticine is used.
Black material is rolled into small balls, but gray material will be needed to create tires. You just need to make small cakes, which in the future are attached to the center of the workpieces. The result is a fairly original and authentic wheel.
Tools and materials Time: 1-5 hours • Difficulty: 7/10
- paper;
- Printer;
- scissors;
- glue.
A short instruction on how to use this assembly. If there is a “download” link under the picture, click on it and save it to your computer. If there is no link under the picture, then save the model you like right away. After that, all that remains is to print the models, cut them out and glue them together.
Other ideas
There are a huge number of motorcycles on the modern market, so the process of creating this vehicle from plasticine may include other nuances. For example, gray and black plasticine can be used for the body and wheels, and some parts can be made red or blue.
An alternative process for creating a motorcycle from plasticine step by step is as follows. First of all, you need to create a medium sized mold to create the fuel tank, which will be red in color. To do this, you need to knead some material in the appropriate color scheme and create the main part, and then give it a suitable shape.
The wheels are created from identical balls, which are best made from black plasticine. In order to give them the required shape, you should use a board or wooden surface. It is advisable to start fastening from both sides, and gray plasticine is usually used for the central part of the wheel. Parts and elements on wheels should be as symmetrical as possible on each side. Now you need to attach the wheels to the frame.
To ensure maximum stability of the motorcycle, it is necessary to create wide wheels. Otherwise, the vehicle will not be able to stand on its own and will constantly tilt to one side.
To create a frame, you can use gray tubes, which will also support the wheels and curved steering wheel. For the frame at the front of the vehicle, I take red material that will attach to the black seat and connect to the fuel tank.
We create blanks for lanterns. One lantern is large in size, the other five are small in size. After they are made, each one must be installed in its place in the front and rear of the vehicle.
